Supermicro CSE-811I-420 Ficha de datos

1.0® SUPERSC811 CHASSISUSER'S GUIDER Rsuperserver 5011Esuperserver 5011HUPER UPERNIC 1NIC 2RESET UPERMICRRNIC 1NIC 2RESET UPERMICRRThe SC811

1-10 SC811 Chassis User’s GuideC. The Power Supply Specifications of the SC811B. The Accessory Kit contains the following:Power supply spec 250W 260W

1-11Chapter 1: Safety Information and Technical SpecificationsD. The Serial ATA Back Panel (*SC811T Only)D-1 Jumper Settings and Pin DefinitionsD-2 Ju

1-12 SC811 Chassis User’s GuideNotes

2-1Chapter 2: Chassis Description and Installation Instructions2-1 Chassis DescriptionA. Contents of the Accessory Kit:The following items are include

2-2 SC811 Chassis User’s GuideC. Chassis Front View and the Front Control PanelA. 1" Hot-swap SCA Drive Bay(2)(*SC811S/T)B. Slim CDROM(1) (*O

2-3Chapter 2: Chassis Description and Installation InstructionsFront Panel LED IndicatorsLED Button Definitions J. OverheatI. LAN2H. LAN1G. HDD Acti

2-4 SC811 Chassis User’s GuideD. Chassis Rear View and the Back Panel*I/O Back PanelBack Panel I/O Port DefinitionsD. Keyboard & MouseSC811 Chass

2-5Chapter 2: Chassis Description and Installation InstructionsB. Tools needed2-2 Chassis InstallationA. Important Safety GuidelinesStopThis product s

2-6 SC811 Chassis User’s GuideC-1. Accessing the SCA Drive Tray and Installing a SCSITo install a SCA drive into the chassis, you need to first remo

2-7Chapter 2: Chassis Description and Installation Instructions3b3aC-2. Accessing the IDE Drive Tray and Installing an IDE HDD21To install an IDE HDD

1-2 SC811 Chassis User’s GuideThe information in this User’s Guide has been carefully reviewed and is believed to beaccurate. The vendor assumes no r

2-8 SC811 Chassis User’s GuideD. Removing the Top Cover of the SC811 ChassisBefore installing any components, replacing chassis fans or accessing t

2-9Chapter 2: Chassis Description and Installation InstructionsE. Accessing the Power SupplyProcedures1. Remove the two screws from the power supply

2-10 SC811 Chassis User’s GuideF. Installing the MotherboardBe sue to disconnect the power supply before accessing or installing the mother-board in

2-11Chapter 2: Chassis Description and Installation Instructions4. Secure the CPU heatsink mechanism to the motherboard.3. Lay the Mylar sheet that ca

2-12 SC811 Chassis User’s GuidePress the Locking TabG. Installing Chassis Rail (-Inner Rails)Please make sure that the chassis covers and chassis rai

2-13Chapter 2: Chassis Description and Installation Instructions3. Locate the five holes on each side of the chassis and locate the five corre-spondi

2-14 SC811 Chassis User’s GuideAfter you have installed the inner rails on the chassis, you are ready to install theouter rails of rail assemblies to

2-15Chapter 2: Chassis Description and Installation Instructions7. Slide the SC811 chassis into the rack as shown below:(The SC811 may not slide into

2-16 SC811 Chassis User’s GuideH-2 Rack Installation for the Open-Rack DesignAfter you have installed the inner rails on the chassis, you are ready t

2-17Chapter 2: Chassis Description and Installation Instructions3. Attach the front (-short) bracket to the front end of the rack, and secure it to

1-3Chapter 1: Safety Information and Technical SpecificationsTable of ContentsChapter I: Safety Information and Technical Specifications ... 1-

2-18 SC811 Chassis User’s Guide5. Measure the depth of your rack and adjust the length of the rails accordingly.Then, secure the rails to the chassis

1-4 SC811 Chassis User’s GuideChapter 1-Safety Information and TechnicalSpecifications1-1 Electrical Safety GuidelinesWarning: To avoid electrical sho

1-5Chapter 1: Safety Information and Technical Specifications Use rubber mats specifically designed as electrical insulators when workingwith compute

1-6 SC811 Chassis User’s Guide1-3 ESD Safety Guidelines Use a grounded wrist strap designed to prevent static discharge. Keep all comp

1-7Chapter 1: Safety Information and Technical SpecificationsTo avoid personal injury and property damage, please carefullyfollow all the safety step

1-8 SC811 Chassis User’s GuideBefore installing the chassis into a rack:1. Make sure that the rack is securely anchored onto a unmovable surface orstr

1-9Chapter 1: Safety Information and Technical Specifications       