1.0® SUPERSC512 CHASSIS USER'S GUIDEThe SC512C/L SeriesThe SC512C SeriesThe SC512L Series
2-2 SC512 Chassis User’s Guide1a. Power On LED 1b. HDD Activity LED1c. NIC1 (LAN1) LED 1d. NIC2 (LAN2) LED1e. Overheat LED 3. Front Contro
2-3Chapter 2: Chassis Description and Installation InstructionsD. Chassis Rear ViewSC512 Chassis Rear View-B-1231. Back Panel and I/O Device Descript
2-4 SC512 Chassis User’s GuideB. Tools needed2-2 Chassis InstallationA. Important Safety GuidelinesThis product shall only be accessed, assembled and
2-5Chapter 2: Chassis Description and Installation InstructionsC. Removing the Top Chassis Cover and the HDD Tray Bracket from the chassisBefore inst
2-6 SC512 Chassis User’s GuideD1. Removing the CD-ROM ModuleBefore installing a CD-ROM into the CD-ROM module, you need to remove the CD-ROM module fr
2-7Chapter 2: Chassis Description and Installation InstructionsD2. Removing the HDD Drive Tray Housing and Installing the HDDsAfter the HDD Drive Tray
2-8 SC512 Chassis User’s GuideAE. Installing the MotherboardBe sure to disconnect the power supply before accessing or installing the motherboard in
2-9Chapter 2: Chassis Description and Installation InstructionsF. Installing and Uninstalling the Heatsink Mechanism1. Do not apply any thermal grease
2-10 SC512 Chassis User’s GuideG. Installing the Cooling Fan Module and the Air ShroudAfter the motherboard and the heatsink(s) have been installed i
2-11Chapter 2: Chassis Description and Installation InstructionsPress the Locking Tab H. Installing Chassis Rails (*Optional)(*Note: if your chassis
1-2 SC512 Chassis User’s GuideThe information in this User’s Guide has been carefully reviewed and is believed to be accurate. The vendor assumes no
2-12 SC512 Chassis User’s Guide3. Locate the three holes on each side of the chassis and locate the three cor-responding holes on each of the
2-13Chapter 2: Chassis Description and Installation InstructionsAfter you have installed the inner rails on the chassis, you are ready to install the
2-14 SC512 Chassis User’s Guide7. Slide the SC512 chassis into the rack as shown below.(The SC512 may not slide into the rack smoothly or easily when
2-15Chapter 2: Chassis Description and Installation Instructions I-2 Installing the Open-Racks (*Optional) After you have installed the inner rails o
2-16 SC512 Chassis User’s Guide3. Attach the front (-short) bracket to the front end of the rack, and secure it to the rack with two Type H scre
2-17Chapter 2: Chassis Description and Installation Instructions5. Measure the depth of your rack and adjust the length of the rails accordingly. Then
2-18 SC512 Chassis User’s Guide J. Installing the SC512 into the Racks Before installing the chassis into the rack:1. Make sure that the rack is
1-3Chapter 1: Safety Information and Technical Specifi cationsTable of ContentsChapter I: Safety Information and Technical Specifi cations ...
1-4 SC512 Chassis User’s Guide Chapter 1- Introduction1-1 Electricity Safety!General Electrical Safety GuidelinesUse the exact type of power cords as
1-5Chapter 1: Safety Information and Technical Specifi cations1-3. General Safety GuidelinesWarning!! Follow the guidelines below to avoid possible dam
1-6 SC512 Chassis User’s Guide1-6 Product Compliance InformationIf integrated with a motherboard validated and recommended by Supermicro, and confi gur
1-7Chapter 1: Safety Information and Technical Specifi cationsA. The SC512 chassis contains the following: 1-7. Packing List and the SC512 Specifi cati
1-8 SC512 Chassis User’s Guide Component QuantityAC Power Cord 1Screws 1 setRackmount Kit 1 (CSE-PT8) –(*optional) SC512 I/O Label 2Hard Disk Driv
2-1Chapter 2: Chassis Description and Installation InstructionsGH FF. Flat head M4 x 4 mm [0.157]RAIL (*Not included in the shipment) RAIL (*Not incl
Comentarios a estos manuales