Supermicro MBD-H8SML-IF-O Manual de usuario

USER’S MANUALRevision 1.0c® SUPERH8SML-7H8SML-iH8SML-7FH8SML-iF

1-4H8SML-7/i(F) SERVERBOARD USER'S MANUALNotes:Jumpers not indicated are for test purposes only.Not all ports, jumpers or LED Indicators are avai

Chapter 1: Introduction1-5H8SML-7/i(F) Quick ReferenceJumper Description Default SettingJBT1 CMOS Clear (See Section 2-7)JI2C1/JI2C2 I2C to PCI-E Slot

1-6H8SML-7/i(F) SERVERBOARD USER'S MANUALConnector Description6-SGPIO1/6-SGPIO2 Serial General Purpose Input/Output Header for SASCOM1/2 COM1 Ser

Chapter 1: Introduction1-71-3 Motherboard FeaturesCPU• One AMD Opteron 3000 series (AMD Socket AM3+ type) processorsMemory• The H8SML-7/i(F) serverb

1-8H8SML-7/i(F) SERVERBOARD USER'S MANUALACPI Features• Microsoft OnNow• Slow blinking LED for suspend state indicator• BIOS support for USB k

Chapter 1: Introduction1-9UDIMM/1600 1BUDIMM/1600 1ASOCKETAM3R2CPUHT3 Link16/16-2.6 GHzUDIMM/1600 2BUDIMM/1600 2APCI-E GEN2 X8Slot7 PCI-E 2.0 x8 (in

1-10H8SML-7/i(F) SERVERBOARD USER'S MANUALHyperTransport TechnologyHyperTransport technology is a high-speed, low latency point to point link tha

Chapter 1: Introduction1-111-6 Power Confi guration SettingsThis section describes the features of your motherboard that deal with power and power sett

1-12H8SML-7/i(F) SERVERBOARD USER'S MANUAL1-7 Power SupplyAs with all computer products, a stable power source is necessary for proper and reliab

Chapter 2: Installation2-1Chapter 2 Installation2-1 Standardized Warning StatementsAbout Standardized Warning StatementsThe following statements are

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccu

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-2Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur du

Chapter 2: Installation2-3Product Disposal Warning!Ultimate disposal of this product should be handled according to all national laws and regulations.

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-42-2 Static-Sensitive DevicesElectrostatic Discharge (ESD) can damage electronic com ponents. To prevent

Chapter 2: Installation2-52-3 Processor and Heatsink InstallationCaution: Exercise extreme caution when handling and installing the processor. Always

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-63. With the lever raised, locate and align pin 1 of the CPU socket with pin 1 of the CPU. Both are mark

Chapter 2: Installation2-72-4 Mounting the Motherboard into a ChassisAll motherboards have standard mounting holes to fi t different types of chassis.

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-8SupportThe H8SML-7/i(F) serverboard supports single/dual channel, DDR3-1600/1333/1066 Mhz speed Unbuffe

Chapter 2: Installation2-9Memory Population for Optimal Performance# DIMMS Channel 1 Channel 22 DIMMs DIMM1A DIMM2A4 DIMMs DIMM1A DIMM1B DIMM2A DIMM2B

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-102-7 I/O Port and Control Panel ConnectionsThe I/O ports are color coded to make setting up your system

Chapter 2: Installation2-11Power Connectors A 24-pin main power supply connector(JPW1) and one 8-pin CPU PWR connector (JPW2) on the motherboard. The

PrefaceiiiPrefaceAbout This ManualThis manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information fo

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-12NIC2 (Activity) LEDThe LED connections for LAN2 are on pins 9 and 10 of JF1. Attach LAN LED cables to d

Chapter 2: Installation2-13Fan Header(FAN1~FAN5)Pin Defi nitionsPin# Defi nition1 Ground2 +12V 3 Tachometer4 PWR ModulationFan HeadersThis motherboar

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-14Universal Serial Bus PortsTwo Universal Serial Bus ports (USB 2.0) are located beside the Keyboard and

Chapter 2: Installation2-15ATX PS/2 Keyboard and PS/2 Mouse PortsThe ATX PS/2 keyboard and PS/2 mouse are located next to the Back Panel USB Ports on

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-16Power LED/SpeakerOn the JD1 header, pins 1~3 are used for power LED indication, and pins 4-7 are for th

Chapter 2: Installation2-17Trusted Platform Module HeaderThe JTPM1 header is used to connect a Trusted Platform Module (TPM), available separately fro

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-182-9 Jumper SettingsExplanation of JumpersTo modify the operation of the motherboard, jumpers can be use

Chapter 2: Installation2-19VGA Enable/DisableJPG1 allows you to enable or disable the VGA port. The default position is on pins 1 and 2 to enable VGA.

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-20SAS Enable/DisableJumper Settings (JPS1)Jumper Setting Defi nitionPins 1-2 EnabledPins 2-3 DisabledSA

Chapter 2: Installation2-21LAN1/LAN2 LEDsThe Ethernet ports (located beside the VGA port) have two LEDs. On each Gb LAN port, one LED blinks to indica

Table of ContentsChapter 1 Introduction1-1 Overview ...

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-22SATA PortsThere are no jumpers to configure the SATA ports, which are designated SATA0 through SATA5. S

Chapter 2: Installation2-232-12 Enabling SATA RAIDNow that the hardware is set up, you must install the operating system and the SATA RAID drivers, i

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-24Figure 2-4. BIOS Setup ScreenEnabling SATA RAID in the BIOSBefore installing the Windows operating syst

Chapter 2: Installation2-25Figure 2-6. Adaptec RAID Utility Program ScreenFigure 2-5. DotHill RAID Utility Program Screen

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-26Using the DotHill and Adaptec RAID UtilityThe RAID Utility program allows you to defi ne the drives you

Chapter 2: Installation2-27Figure 2-7. Driver/Tool Installation Display Screen2-13 Installing DriversThe Supermicro Website contains drivers and utili

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-28SuperDoctor IIIThe SuperDoctor® III program is a Web base management tool that supports remote manageme

Chapter 2: Installation2-29Note: The SuperDoctor III program and User’s Manual can be downloaded from the Supermicro web site at http://www.supermicro

H8SML-7/i(F) SERVERBOARD USER'S MANUAL2-302-14 Serverboard BatteryCaution: There is a danger of explosion if the onboard battery is installed ups

3-1Chapter 3: TroubleshootingChapter 3 Troubleshooting3-1 Troubleshooting ProceduresUse the following procedures to troubleshoot your system. If you h

Power On LED ... 2-13NMI Button ...

3-2H8SML-7/i(F) SERVERBOARD USER'S MANUALNo Video1. If the power is on but you have no video, remove all the add-on cards and cables.2. Use the

3-3Chapter 3: Troubleshooting2. BIOS upgrades can be downloaded from our web site. Note: Not all BIOS can be fl ashed depending on the modifi cations t

3-4H8SML-7/i(F) SERVERBOARD USER'S MANUALQuestion: What's on the CD that came with my motherboard?Answer: The supplied compact disc has quit

Chapter 4: BIOS4-1Chapter 4 BIOS4-1 IntroductionThis chapter describes the AMIBIOS™ Setup utility for the H8SML-7/i(F) serverboard. The 16 Mb AMI BIOS

4-2H8SML-7/i(F) SERVERBOARD USER'S MANUAL4-2 Main MenuFigure 4-1: Main BIOS ScreenWhen you fi rst enter AMI BIOS Setup Utility, you will see the M

Chapter 4: BIOS4-34-3 Advanced Settings Menu Boot FeatureQuick BootIf Enabled, this option will skip certain tests during POST to reduce the time ne

4-4H8SML-7/i(F) SERVERBOARD USER'S MANUALPower Button FunctionThis sets the function of the power button when you turn off the system. Options in

Chapter 4: BIOS4-5Power CapThis option can decide the highest P-state in the OS. Options include P-state 0 through P-state 4.HPC ModeThis option Enabl

4-6H8SML-7/i(F) SERVERBOARD USER'S MANUALCS Sparing EnableThis setting will reserve a spare memory rank in each node when enabled. Options are En

Chapter 4: BIOS4-7 SouthBridge Confi gurationOHCI/EHCI HC Device FunctionsThese settings allow you to either Enable or Disable functions for OHCI or E

Table of ContentsInstalling the OS/SATA Driver ... 2-23Building a Driver Diskette

4-8H8SML-7/i(F) SERVERBOARD USER'S MANUALPATA Channel Confi gurationThis allows you to set PATA channel confi guration. Options include SATA as Pr

Chapter 4: BIOS4-9S.M.A.R.T.Self-Monitoring Analysis and Reporting Technology (SMART) can help predict impending drive failures. Select "Auto&quo

4-10H8SML-7/i(F) SERVERBOARD USER'S MANUALPCIE x8 Slot7These settings Enable or Disable the specifi ed PCIE slot in your system.Onboard LAN Option

Chapter 4: BIOS4-11 Remote Access Confi gurationRemote AccessUse this option to Enable or Disable Remote Access in your system. If enabled, the settin

4-12H8SML-7/i(F) SERVERBOARD USER'S MANUAL Hardware Health Confi gurationCPU Overheat AlarmThis setting allows you to specify the type of alarm

Chapter 4: BIOS4-13When COA (either Early or Default Alarm) is enabled, the following actions are required to be executed:• System overheating LED is

4-14H8SML-7/i(F) SERVERBOARD USER'S MANUALACPI Version FeaturesUse this setting the determine which ACPI version to use. Options are ACPI v1.0, A

Chapter 4: BIOS4-15IP AddressThis submenu sets the IP address source as either Static or DHCP. Selecting Static allows you to manually set the IP Addr

4-16H8SML-7/i(F) SERVERBOARD USER'S MANUAL4-3 Security MenuAMI BIOS provides a Supervisor and a User password. If you use both passwords, the Sup

Chapter 4: BIOS4-17Hard Disk DrivesThis feature allows you to specify the boot sequence from the list of available hard disk drives. A device that i

Chapter 1: Introduction1-1Chapter 1 Introduction1-1 OverviewChecklistCongratulations on purchasing your computer motherboard from an acknowledged lead

4-18H8SML-7/i(F) SERVERBOARD USER'S MANUAL4-5 Exit MenuSelect the Exit tab from AMI BIOS Setup Utility screen to enter the Exit BIOS Setup screen

Appendix A BIOS Error Beep CodesDuring the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occu

A-2H8SML-7/i(F) SERVERBOARD USER'S MANUALNotes

B-1Appendix B: BIOS POST Checkpoint CodesAppendix B BIOS POST Checkpoint CodesWhen AMIBIOS performs the Power On Self Test, it writes checkpoint codes

B-2H8SML-7/i(F) Serverboard User’s ManualB-2 Bootblock Recovery CodesThe bootblock recovery checkpoint codes are listed in order of execution:Checkpo

B-3Appendix B: BIOS POST Checkpoint CodesB-3 Uncompressed Initialization CodesThe following runtime checkpoint codes are listed in order of execution

B-4H8SML-7/i(F) Serverboard User’s ManualCheckpoint Code Description2Ah Bus initialization system, static, output devices will be done next, if presen

B-5Appendix B: BIOS POST Checkpoint CodesCheckpoint Code Description52h The memory above 1 MB has been tested and initialized. Saving the memory size

B-6H8SML-7/i(F) Serverboard User’s ManualCheckpoint Code Description97h Initialization before the C800 adaptor ROM gains control has completed. The ad

1-2H8SML-7/i(F) SERVERBOARD USER'S MANUAL1-2 Contacting SupermicroHeadquartersAddress: Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131

Chapter 1: Introduction1-3Figure 1-1. H8SML-7/i(F) Image