Supermicro SuperServer 1027R-WC1R Manual de usuario Pagina 65
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 5: Advanced Serverboard Setup
5-17
Ethernet Ports
Two Ethernet ports are located on
the I/O backplane. LAN ports 1/2
support gigabit LAN connections
on the C9DRW-CF31, and support
10 Gigabit LAN connections on the
X9DRW-CTF31. In addition, an IPMI_
Dedicated LAN, located above USB
0/1 ports on the backplane, provides
KVM support for IPMI 2.0. These ports
accept RJ45 type cables.
Universal Serial Bus (USB)
Four Universal Serial Bus ports (USB
0/1, USB 2/3) are located on the I/O
back panel. In addition, one USB
header, located close to the LSI 3108
chip, provides two front-accessible
USB connections (USB 4/5, cables
are not included). See the tables on
the right for pin defi nitions.
FP USB (4/5)
Pin Defi nitions
USB 4, 8, 6,
Pin # Defi nition
USB 5, 9
Pin # Defi nition
1 +5V 1 +5V
2 PO- 2 PO-
3 PO+ 3 PO+
4 Ground 4 Ground
5 NC 5 Key
Backplane
USB (0/1, 2/3)
Pin Defi nitions
Pin# Defi nition
1 +5V
2 PO-
3 PO+
4 Ground
5NA
LAN Ports
Pin Defi nition
Pin# Defi nition Pin# Defi nition
1 P2V5SB 10 SGND
2 TD0+ 11 Act LED
3 TD0- 12 P3V3SB
4 TD1+ 13 Link 100 LED (Yel-
low, +3V3SB)
5 TD1- 14 Link 1000 LED
(Yellow, +3V3SB)
6 TD2+ 15 Ground
7 TD2- 16 Ground
8 TD3+ 17 Ground
9 TD3- 18 Ground
UID Switch
Pin# Defi nition
1 Ground
2 Ground
3 Button In
4 Ground
Unit Identifi er Switch
The UID Switch is located on the
backplane. The Rear UID LED (LED3)
is located next to the UID switch. The
control panel UID LED connection is
on pins 7/8 of JF1. Connect a cable
to pin 8 on JF1 for Front Panel UID
LED indication. When you press the
UID switch, both the rear UID LED
and control panel UID LED indicators
will be turned on. Press the UID switch
again to turn off both LED Indicators.
These indicators provide easy identi-
fi cation of a system unit that may be
in need of service. UID can also be
triggered via IPMI.
UID LED
Status
Color/State OS Status
Blue: On Windows OS Unit Identifi ed
Blue:
Blinking
Linux OS Unit Identifi ed
- SUPER 1
- Manual Revision 1.0 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- System Block Diagram 12
- 1-4 Contacting Supermicro 13
- Chapter 2 15
- Server Installation 15
- 2-4 Warnings and Precautions 16
- Rack Mounting Considerations 17
- Inner Rails 18
- Inner Rail 18
- Extensions 18
- Inner Rail Extension 19
- Outer Rails 20
- Chapter 3 25
- System Interface 25
- 3-3 Control Panel LEDs 26
- 3-4 Hard Drive Carrier LEDs 28
- Chapter 4 29
- ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ 31
- Installation Instructions 32
- Circuit Breaker 33
- Power Disconnection Warning 34
- ילמשח קותינ ינפמ הרהזא 35
- Equipment Installation 36
- Restricted Area 37
- Battery Handling 38
- Redundant Power Supplies 40
- Backplane Voltage 41
- Product Disposal 43
- רצומה קוליס 44
- Power Cable and AC Adapter 46
- (UL/CSA ﻞﻤﺤﺗ ﻲﺘﻟﺍﺔﻣﻼﻋ ) 47
- Chapter 5 49
- Advanced Serverboard Setup 49
- • Control Panel cable (JF1) 50
- 5-3 Rear I/O Ports 51
- OPEN 1st 52
- WARNING! 53
- 5-5 Installing Memory 56
- DIMM Module Population Table 57
- 5-6 Adding PCI Add-On Cards 59
- 5-7 Serverboard Details 60
- 5-8 Connector Defi nitions 62
- USB 4, 8, 6 65
- Pin # Defi nition 65
- USB 5, 9 65
- Pin # Defi nition 65
- 5-9 Jumper Settings 68
- 5-10 Onboard Indicators 71
- 5-11 SATA and SAS Ports 72
- 5-12 Installing Software 73
- SuperDoctor® 5 74
- 5-13 Onboard Battery 75
- Chapter 6 77
- Advanced Chassis Setup 77
- 6-2 Control Panel 78
- 6-3 System Fans 79
- Checking the Airfl ow 81
- Accessing the Drive Bays 81
- Hard Drive Installation 81
- 6-5 Power Supply 84
- Chapter 7 85
- 7-2 Main Setup 86
- Boot Features 87
- Power Confi guration 88
- CPU Confi guration 88
- Chipset Confi guration 93
- North Bridge 93
- Integrated IO Confi guration 93
- QPI Confi guration 94
- DIMM Confi guration 95
- DIMM Information 95
- South Bridge Confi guration 97
- SATA Confi guration 98
- PCIe/PCI/PnP Confi guration 99
- Super IO Confi guration 100
- COM Confi guration 101
- • COM 1 and SOL 102
- ACPI Setting 105
- TPM Enable Status 106
- • ME BIOS Interface Version 107
- • ME Version 107
- 7-5 IPMI 109
- BMC Network Confi guration 110
- 7-6 Boot 111
- • 1st Device 112
- • 1st Boot Device 112
- 7-8 Save & Exit 113
- • LAN Device 114
- • UEFI: Built-in EFI Shell 114
- Appendix A 115
- BIOS Error Beep Codes 115
- Appendix B 117
- System Specifi cations 117
Relacionado con productos y manuales para Barebones Servidor Supermicro SuperServer 1027R-WC1R
Barebones Servidor Supermicro 188411 Manual de usuario
(122 paginas)
(122 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales