Supermicro SuperServer 7047R-TXRF Manual de usuario Pagina 1

SUPERSERVER 7047R-TXRF SUPER®USER’S MANUALRevision 1.0

1-2SUPERSERVER 7047R-TXRF User's Manual1-2 Serverboard FeaturesAt the heart of the SuperServer 7047R-TXRF lies the X9DRX+-F, a dual processor se

7-26SUPERSERVER 7047R-TXRF User's ManualPCI Error Logging SupportSelect Enabled to support error event logging for PCI slots. The options are Ena

Chapter 7: BIOS7-17-5 IPMIUse this feature to congure Intelligent Platform Management Interface (IPMI) settings. IPMI Firmware RevisionThi

7-28SUPERSERVER 7047R-TXRF User's ManualWhen SEL is FullThis feature allows the user to decide what the BIOS should do when the system event log

Chapter 7: BIOS7-1Gateway IP AddressThis item displays the Gateway IP address for this computer. This should be in decimal and in dotted quad form (i.

7-30SUPERSERVER 7047R-TXRF User's Manual7-7 SecurityThis menu allows the user to congure the following security settings for the s

Chapter 7: BIOS7-17-8 Save & ExitThis submenu allows the user to congure the Save and Exit settings for the system.Discard Changes

7-32SUPERSERVER 7047R-TXRF User's ManualDiscard ChangesSelect this feature and press <Enter> to discard all the changes and return to the B

A-1Appendix A: BIOS POST Error CodesAppendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time th

A-2SUPERSERVER 7047R-TXRF User's ManualNotes

B-1Appendix B: System SpecicationsAppendix B System SpecicationsProcessorsTwo E5-2600 Series processors in LGA 2011 socketsNote: Please refer to o

1-3Chapter 1: Introductionhardware status remotely, receive an alarm automatically if a failure occurs, and power cycle a system that is non-responsiv

B-2SUPERSERVER 7047R-TXRF User's ManualChassisSC747TQ-R1K28NBP (4U/Tower rackmount)Dimensions: (WxHxD) 11.8 x 7 x 29.4 in. (452 x 178 x 746 mm) W

B-3Appendix B: System Specications

B-4SUPERSERVER 7047R-TXRF User's Manual(continued from front)The products sold by Supermicro are not intended for and will not be used in life su

1-4SUPERSERVER 7047R-TXRF User's ManualFigure 1-1. Intel C602 Chipset: System Block DiagramNote: This is a general block diagram. Please see Ch

1-5Chapter 1: Introduction1-4 Contacting SupermicroHeadquartersAddress: Super Micro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.Tel: +1 (4

1-6SUPERSERVER 7047R-TXRF User's ManualNotes

Chapter 2: Server Installation2-1Chapter 2 System Setup2-1 OverviewThis chapter provides a quick setup checklist to get your SuperServer 7047R-TXRF

2-2SUPERSERVER 7047R-TXRF User's Manual2-3 Preparing for SetupThe box your server was shipped in may include two sets of rail assemblies, two ra

Chapter 2: Server Installation2-3•Install the heaviest server components on the bottom of the rack rst, and then work up.•Use a regulating uninterr

2-4SUPERSERVER 7047R-TXRF User's ManualReliable GroundA reliable ground must be maintained at all times. To ensure this, the rack itself should b

Chapter 2: Server Installation2-5Figure 2-1. Removing the Feet and Chassis Top CoverChassis CoverChassis FeetChassis Cover Lock

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccu

2-6SUPERSERVER 7047R-TXRF User's ManualFigure 2-2. Identifying the Inner Rails and Chassis HandlesChassis HandleInner RailsInstalling the Chassi

Chapter 2: Server Installation2-7Figure 2-3. Installing the Inner Rack Rails Installing the Outer Rails to the RackInstalling the Outer Rails1. Attac

2-8SUPERSERVER 7047R-TXRF User's ManualFigure 2-5. Installing the Rack RailsInstalling the Chassis into a RackInstalling the Chassis1. Conrm t

Chapter 2: Server Installation2-92-5 Tower Mounting InstructionsThe SC747 chassis is shipped with the chassis cover and feet pre-installed. To use th

2-10SUPERSERVER 7047R-TXRF User's ManualInstalling Feet on the ChassisInstalling the Chassis Feet1. Place the chassis foot in the foot receptacl

Chapter 3: System Interface3-1Chapter 3 System Interface3-1 OverviewThere are several LEDs on the control panel as well as others on the drive carri

3-2SUPERSERVER 7047R-TXRF User's Manual3-2 Control Panel ButtonsThere are two push-buttons located on the front of the chassis. These are power

Chapter 3: System Interface3-3NIC1Indicates network activity on GLAN1 when ashing.NIC2Indicates network activity on GLAN2 when ashing.Overheat/Fan F

3-4SUPERSERVER 7047R-TXRF User's Manual3-4 Drive Carrier LEDsEach SAS/SATA drive carrier has two LEDs.•Green: Each drive carrier has a green LE

Chapter 4: System Safety4-1Chapter 4 System Safety4-1 Electrical Safety Precautions!Basic electrical safety precautions shall be followed to protec

PrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It provides information for the installation an

4-2SUPERSERVER 7047R-TXRF User's Manual4-2 General Safety PrecautionsFollow these rules to ensure general safety:•Keep the area around the serv

Chapter 4: System Safety4-34-3 ESD Precautions Electrostatic Discharge (ESD) is generated by two objects with different electrical charges coming int

4-4SUPERSERVER 7047R-TXRF User's Manual4-4 Operating Precautions Care must be taken to assure that the chassis cover is in place when the sys

Chapter 5: Advanced Serverboard Setup5-1Chapter 5 Advanced Serverboard SetupThis chapter covers the steps required to install the X9DRX+-F serverboa

5-2SUPERSERVER 7047R-TXRF User's ManualUnpackingThe serverboard is shipped in antistatic packaging to avoid electrical static discharge. When un

Chapter 5: Advanced Serverboard Setup5-3Rear I/O Ports1. COM1 Port 2. USB0 Port3. USB1 Port 4. Dedicated IPMI LAN Port5. USB2 Port 6. USB3 Port7. LAN

5-4SUPERSERVER 7047R-TXRF User's Manual!1. There are two levers on the LGA2011 socket. First press and release the load lever labeled 'Open

Chapter 5: Advanced Serverboard Setup5-5Gently push down to pop the load plate open.3. With the lever labeled 'Close 1st' fully retracted,

5-6SUPERSERVER 7047R-TXRF User's ManualWarning: You can only install the CPU to the socket in one direction. Make sure that the CPU is properly

Chapter 5: Advanced Serverboard Setup5-7Installing the Heatsink1. Do not apply any thermal grease to the heatsink or the CPU die; the required amount

SUPERSERVER 7047R-TXRF User's Manualivwhen adding or removing processors or main memory and when reconguring the serverboard.Chapter 6: Advanced

5-8SUPERSERVER 7047R-TXRF User's ManualInstalling Memory Modules1. Insert the desired number of DIMMs into the memory slots, starting with P1-DI

Chapter 5: Advanced Serverboard Setup5-9Memory Support for the X9DRX+-F ServerboardThe X9DRX+-F serverboard supports up to 512 GB of DDR3-1333/1066/80

5-10SUPERSERVER 7047R-TXRF User's ManualUDIMM Memory SupportRanks Per DIMM & Data WidthMemory Capacity Per DIMM (Note)SRx8 Non-ECC1GB 2GB 4GB

Chapter 5: Advanced Serverboard Setup5-11 Press the Middle of the Release TabLift the Release TabFigure 5-7: Add-on Card/Expansion Ca

5-12SUPERSERVER 7047R-TXRF User's ManualFigure 5-8. X9DRX+-F Layout(not drawn to scale)5-7 Serverboard DetailsNote: Jumpers not indicated are f

Chapter 5: Advanced Serverboard Setup5-13X9DRX+-F Jumpers Jumper Description Default Setting JBT1 Clear CMOS See Section 5-9JI2C1/JI2C2 SMB to PCI-E S

5-14SUPERSERVER 7047R-TXRF User's Manual5-8 Connector Denitions Power ConnectionsA 24-pin main power supply connector(JPW1), two 8-pin CPU PWR

Chapter 5: Advanced Serverboard Setup5-15NIC1/NIC2 LED IndicatorsThe NIC (Network Interface Controller) LED connection for GLAN port 1 is located on p

5-16SUPERSERVER 7047R-TXRF User's ManualPower Button The Power Button connection is located on pins 1 and 2 of JF1. Momentarily contacting both p

Chapter 5: Advanced Serverboard Setup5-17Ethernet PortsTwo Gigabit Ethernet ports (LAN1, LAN2) are located on the I/O backplane. In addition, a dedica

vPrefaceNotes

5-18SUPERSERVER 7047R-TXRF User's ManualChassis Intrusion A Chassis Intrusion header is located at JL1 on the serverboard. Attach an appropriate

Chapter 5: Advanced Serverboard Setup5-19TPM Header/Port 80 HeaderA Trusted Platform Module/Port 80 header is located at JTPM1 to provide TPM support

5-20SUPERSERVER 7047R-TXRF User's Manual3-SGPIO 1/2/3 HeadersThree SGPIO (Serial-Link General Purpose Input/Output) headers are located on the se

Chapter 5: Advanced Serverboard Setup5-215-9 Jumper SettingsExplanation of JumpersTo modify the operation of the serverboard, jumpers can be used to

5-22SUPERSERVER 7047R-TXRF User's ManualLAN1/2 Enable/Disable Change the setting of jumper JPL1 to enable or disable the LAN1/LAN2 Ethernet ports

Chapter 5: Advanced Serverboard Setup5-23GLAN LEDsThere are two GLAN ports on the serverboard. An additional IPMI dedicated LAN port is also located a

5-24SUPERSERVER 7047R-TXRF User's Manual5-11 SATA PortsSerial ATAPin Denitions Pin# Denition1 Ground2 TX_P3 TX_N4 Ground5 RX_N6 RX_P7 Groun

Chapter 5: Advanced Serverboard Setup5-255-12 Installing SoftwareAfter the hardware has been installed, you should rst install the operating system

5-26SUPERSERVER 7047R-TXRF User's ManualSupero Doctor IIIThe Supero Doctor III program is a Web base management tool that supports remote managem

Chapter 5: Advanced Serverboard Setup5-27Note: SD III Software Revision 1.0 can be downloaded from our Web Site at: ftp://ftp.supermicro.com/utility/S

viTable of ContentsChapter 1 Introduction1-1 Overview ...

5-28SUPERSERVER 7047R-TXRF User's ManualNotes

Chapter 6: Advanced Chassis Setup6-1Chapter 6 Advanced Chassis SetupThis chapter covers the steps required to install components and perform mainten

6-2SUPERSERVER 7047R-TXRF User's Manual6-1 Static-Sensitive DevicesElectrostatic Discharge (ESD) can damage electronic com ponents. To prevent d

Chapter 6: Advanced Chassis Setup6-36-3 System CoolingSix heavy-duty fans provide cooling for the chassis. Four fans are located in the mid-section o

6-4SUPERSERVER 7047R-TXRF User's ManualRear Fan Release TabFigure 6-4. Rear System Chassis FansFigure 6-3. Mid-System Chassis FansMid Fan Relea

Chapter 6: Advanced Chassis Setup6-56-4 Power SupplyThe SC747 chassis has a 1280W (redundant) power supply. This power supply is auto-switching capab

6-6SUPERSERVER 7047R-TXRF User's ManualPower Supply Cables Name Qty Connects to: Description20-pin or 24-pin power cable1 Serverboard20-pin or 24

Chapter 6: Advanced Chassis Setup6-76-5 Conguring the Storage Module This section covers conguring the storage module in the SC747 chassis.Storage

6-8SUPERSERVER 7047R-TXRF User's ManualRotating the Storage Module for Rack Mounting1. Open the chassis cover.2. Locate the storage module and

Chapter 6: Advanced Chassis Setup6-9Figure 6-9. Chassis Storage Module5. Turn the storage module 90 degrees (as illustrated).6. Reinsert the module

viiTable of ContentsInstalling Feet on the Chassis ... 2-10Chapter 3 System Interfa

6-10SUPERSERVER 7047R-TXRF User's ManualRemoving a Drive CarrierUse the procedure below to add hard drives to the drive carriers.Adding Hard Driv

Chapter 6: Advanced Chassis Setup6-11Hard DriveHard Drive TrayFigure 6-11. Adding a Hard Drive to the Drive Carrier4. Place the hard drive to the ha

6-12SUPERSERVER 7047R-TXRF User's ManualAdding Peripheral DrivesYou can add up to three peripheral drives (DVD-ROM, CD-ROM, oppy drive, etc.) to

Chapter 6: Advanced Chassis Setup6-136-6 Installing Hard Drives in the ChassisChassis hard drives are mounted in drive carriers to simplify their ins

6-14SUPERSERVER 7047R-TXRF User's ManualFigure 6-14. Removing a Dummy Drive Tray7. Insert the hard drive into the chassis. To do this:a. Press

Chapter 7: BIOS7-1Chapter 7 BIOS 7-1 IntroductionThis chapter describes the AMI BIOS Setup utility for the X9DRX+-F. It also provides the instruct

7-2SUPERSERVER 7047R-TXRF User's ManualHow To Change the Conguration DataThe conguration data that determines the system parameters may be chan

Chapter 7: BIOS7-1The AMI BIOS main menu displays the following information:System DateThis item displays the system date in Day MM/DD/YY format (e.g.

7-4SUPERSERVER 7047R-TXRF User's Manual7-3 Advanced Setup CongurationsUse the arrow keys to select Advanced Setup and press <Enter> to a

Chapter 7: BIOS7-1Interrupt 19 CaptureInterrupt 19 is the software interrupt that handles the boot disk function. When this item is set to Enabled, th

viii5-12 Installing Software ... 5-25Supero Doctor III ...

7-6SUPERSERVER 7047R-TXRF User's Manual•CPU Stepping•Maximum CPU Speed•Minimum CPU Speed•Processor Cores•Intel HT (Hyper-Threading) Technolo

Chapter 7: BIOS7-1Limit CPUID MaximumThis feature allows the user to set the maximum CPU ID value. Enable this function to boot the legacy operating s

7-8SUPERSERVER 7047R-TXRF User's ManualIntel® Virtualization Technology (Available when supported by the CPU)Select Enabled to support Intel Virt

Chapter 7: BIOS7-1CPU C6 Report (Available when Power Technology is set to Custom)Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3

7-10SUPERSERVER 7047R-TXRF User's ManualShort Duration Power LimitThis item displays the time period during which short duration power is main-ta

Chapter 7: BIOS7-1CPU1 Slot 1 PCI-E 3.0 x8 Link SpeedThis feature allows the user to set the PCI-Exp bus speed for the slot specied above. The option

7-12SUPERSERVER 7047R-TXRF User's ManualDIMM CongurationThis section displays the following DIMM information.Current Memory ModeThis item displ

Chapter 7: BIOS7-1Channel InterleavingThis feature selects from the different channel interleaving methods. The options are Auto, 1 Way, 2 Way, 3, Way

7-14SUPERSERVER 7047R-TXRF User's ManualSouth Bridge CongurationThis feature allows the user to congure the settings for the Intel PCH chip.PC

Chapter 7: BIOS7-1SATA CongurationWhen this submenu is selected, the AMI BIOS automatically detects the presence of IDE or SATA devices and displays

Chapter 1 Introduction1-1 OverviewThe SuperServer 7047R-TXRF is comprised of two main subsystems: the SC747TQ-R1K28NBP 4U/Tower server chassis and t

7-16SUPERSERVER 7047R-TXRF User's ManualRAID ModeThe following items are displayed when RAID Mode is selected:Port 0~5 Hot PlugSelect Enabled to

Chapter 7: BIOS7-1SERR# GenerationSelect Enabled to allow a PCI device to generate an SERR number for a PCI Bus Signal Error Event. The options are En

7-18SUPERSERVER 7047R-TXRF User's ManualLoad Onboard SAS Option ROMSelect Enabled to use the SAS Option ROM to boot the computer using a network

Chapter 7: BIOS7-1Device SettingsThis item displays the settings of Serial Port 2.Change SettingsUse this feature to set the optimal Environment Contr

7-20SUPERSERVER 7047R-TXRF User's ManualBits Per secondUse this feature to set the transmission speed for a serial port used in Console Redirecti

Chapter 7: BIOS7-1Legacy OS Redirection ResolutionUse this feature to select the number of rows and columns used in Console Redirection for legacy OS

7-22SUPERSERVER 7047R-TXRF User's ManualFlow ControlThis feature allows the user to set the ow control for Console Redirection to p

Chapter 7: BIOS7-1Pending Operation: This item displays the status of a pending operation.Current Status Information: This item displays the informati

7-24SUPERSERVER 7047R-TXRF User's ManualIntel ME Subsystem CongurationThis feature displays the following ME Subsystem Conguration settings.•

Chapter 7: BIOS7-1•Factory MAC Address•Alternate MAC Address7-4 Event LogsUse this feature to congure Event Log settings.Change SMBIOS Event Log