Supermicro SuperServer 7047R-TXRF Manual de usuario Pagina 63
- Pagina / 112
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 6: Advanced Chassis Setup
6-3
6-3 System Cooling
Six heavy-duty fans provide cooling for the chassis. Four fans are located in the
mid-section of the chassis with two fans in the rear. These fans circulate air through
the chassis as a means of lowering the chassis internal temperature.
The fans come pre-installed to the chassis. Each fan is hot-swappable and can be
replaced without removing any connections.
System Fan Failure
Fan speed is controlled by system temperature via a BIOS setting. If a fan fails, the
remaining fans will ramp up to full speed. Replace any failed fan at your earliest
convenience with the same type and model (the system can continue to run with
a failed fan).
Replacing System Fans
The SC747 chassis contains two types of system fans: mid-system fans and rear
system fans.
Replacing Mid-System Fans
1. Determine which fan has failed. Because the fans are hot-swappable, the
chassis does not need to be powered-down.
2. Press the fan release tab and lift the failed fan from the chassis. Mid fans
must be pulled straight out of the chassis (see Figure 6-3).
3. Place the new fan into the vacant space in the housing while making sure
the arrows on the top of the fan (indicating air direction) point in the same
direction as the arrows on the other fans. As soon as the fan is connected, it
will begin working.
Replacing the Rear System Fan
1. Determine which fan is not operation
2. Press the rear fan release tab (see Figure 6-4).
3. Pull the fan away from the chassis by pulling out the top rst.
4. Place the new fan in the chassis, inserting the bottom of the fan rst.
5. Push the fan fully into the housing until the fan clicks into place.
- SUPER 1
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 3 System Interface 7
- Chapter 4 System Safety 7
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- DMI: LANE 12
- Reversal 12
- 1-4 Contacting Supermicro 13
- Chapter 2 15
- System Setup 15
- 2-3 Preparing for Setup 16
- Warnings and Precautions! 16
- •Allow the hot plug SMicro12 17
- Reliable Ground 18
- Chassis Cover 19
- Chassis Feet 19
- Chassis Cover Lock 19
- Chassis Handle 20
- Inner Rails 20
- Slide into the Inner Rail 21
- Secure to the 21
- Rear of the Rack 21
- Attach to Middle Rail 21
- Installing the Chassis Cover 23
- Chassis Foot 24
- Receptacle 24
- Chassis Screw 24
- Chapter 3 25
- System Interface 25
- 3-2 Control Panel Buttons 26
- 3-3 Control Panel LEDs 26
- Overheat/Fan Fail 27
- Power Fail 27
- 3-4 Drive Carrier LEDs 28
- Chapter 4 29
- System Safety 29
- 4-3 ESD Precautions 31
- 4-4 Operating Precautions 32
- Chapter 5 33
- Advanced Serverboard Setup 33
- •Control Panel cable (JF1) 34
- 5-3 I/O Ports 35
- OPEN 1st 36
- WARNING! 36
- 5-6 Installing Memory 40
- UDIMM Memory Support 42
- RDIMM Memory Support 42
- LRDIMM Memory Support 42
- 5-6 Adding PCI Add-On Cards 43
- 5-7 Serverboard Details 44
- 5-8 Connector Denitions 46
- USB 4, 5, 6,8 48
- Pin # Denition 48
- USB 7, 9 48
- Pin # Denition 48
- VGA Enable/Disable Jumper 53
- Settings 53
- Jumper Setting Denition 53
- Pins 1-2 Enabled 53
- Pins 2-3 Disabled 53
- 5-10 Onboard Indicators 55
- 5-11 SATA Ports 56
- 5-12 Installing Software 57
- Supero Doctor III 58
- Chapter 6 61
- Advanced Chassis Setup 61
- 6-1 Static-Sensitive Devices 62
- 6-2 Control Panel 62
- 6-3 System Cooling 63
- Rear Fan Release 64
- Mid Fan 64
- Release Tab 64
- 6-4 Power Supply 65
- Power Supply Connections 66
- Tower or Rack Conguration 67
- Rotating the Storage Module 68
- Removing a Drive Carrier 70
- Hard Drive 71
- Hard Drive Tray 71
- Adding Peripheral Drives 72
- Drive Tray Handle 73
- Release Button 73
- Drive Tray 74
- SAS/SATA 74
- Chapter 7 75
- 7-2 Main Setup 76
- Boot Features 78
- •Type of CPU 79
- •CPU Signature 79
- •Microcode Patch 79
- Chipset Conguration 84
- North Bridge 84
- Integrated IO Conguration 84
- QPI Conguration 85
- DIMM Conguration 86
- DIMM Information 86
- South Bridge Conguration 88
- SATA Conguration 89
- PCIe/PCI/PnP Conguration 90
- Super IO Conguration 92
- Serial Port 1 Conguration 92
- Serial Port 2 Conguration 92
- Console Redirection Settings 93
- Console Redirection Settings 95
- ACPI Settings 96
- TPM Enable Status 97
- NIC Conguration 98
- •Factory MAC Address 99
- •Alternate MAC Address 99
- 7-5 IPMI 101
- BMC Network Conguration 102
- 7-6 Boot 103
- 7-7 Security 104
- 7-8 Save & Exit 105
- Appendix A 107
- BIOS Error Beep Codes 107
- Appendix B 109
- System Specications 109
Relacionado con productos y manuales para Barebones Servidor Supermicro SuperServer 7047R-TXRF
Barebones Servidor Supermicro 188411 Manual de usuario
(122 paginas)
(122 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.191 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales