Supermicro SuperServer 7047R-TXRF Manual de usuario descargar pdf (Pagina 73)

Chapter 6: Advanced Chassis Setup

6-13

6-6 Installing Hard Drives in the Chassis

Chassis hard drives are mounted in drive carriers to simplify their installation and

removal from the chassis. These carriers also help promote proper airow for the

drive bays.

Installing Hard Drives

1. Unlock and open the chassis cover.

2. Press the release button to extend the drive tray handle (see Figure 6-13).

3. Using the handle, pull the drive tray out by the handle. The drive is hot

swappable; there are no cables to disconnect.

4. Remove the screws holding the drive tray to the dummy drive.

Drive Tray Handle

Release Button

Figure 6-13. Installing Hard Drives

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 111 112

SUPER 1
About This Manual 3
Manual Organization 3
Table of Contents 6
Chapter 3 System Interface 7
Chapter 4 System Safety 7
Chapter 1 9
Introduction 9
1-2 Serverboard Features 10
1-3 Server Chassis Features 11
DMI: LANE 12
Reversal 12
1-4 Contacting Supermicro 13
Chapter 2 15
System Setup 15
2-3 Preparing for Setup 16
Warnings and Precautions! 16
•Allow the hot plug SMicro12 17
Reliable Ground 18
Chassis Cover 19
Chassis Feet 19
Chassis Cover Lock 19
Chassis Handle 20
Inner Rails 20
Slide into the Inner Rail 21
Secure to the 21
Rear of the Rack 21
Attach to Middle Rail 21
Installing the Chassis Cover 23
Chassis Foot 24
Receptacle 24
Chassis Screw 24
Chapter 3 25
System Interface 25
3-2 Control Panel Buttons 26
3-3 Control Panel LEDs 26
Overheat/Fan Fail 27
Power Fail 27
3-4 Drive Carrier LEDs 28
Chapter 4 29
System Safety 29
4-3 ESD Precautions 31
4-4 Operating Precautions 32
Chapter 5 33
Advanced Serverboard Setup 33
•Control Panel cable (JF1) 34
5-3 I/O Ports 35
OPEN 1st 36
WARNING! 36
5-6 Installing Memory 40
UDIMM Memory Support 42
RDIMM Memory Support 42
LRDIMM Memory Support 42
5-6 Adding PCI Add-On Cards 43
5-7 Serverboard Details 44
5-8 Connector Denitions 46
USB 4, 5, 6,8 48
Pin # Denition 48
USB 7, 9 48
Pin # Denition 48
VGA Enable/Disable Jumper 53
Settings 53
Jumper Setting Denition 53
Pins 1-2 Enabled 53
Pins 2-3 Disabled 53
5-10 Onboard Indicators 55
5-11 SATA Ports 56
5-12 Installing Software 57
Supero Doctor III 58
Chapter 6 61
Advanced Chassis Setup 61
6-1 Static-Sensitive Devices 62
6-2 Control Panel 62
6-3 System Cooling 63
Rear Fan Release 64
Mid Fan 64
Release Tab 64
6-4 Power Supply 65
Power Supply Connections 66
Tower or Rack Conguration 67
Rotating the Storage Module 68
Removing a Drive Carrier 70
Hard Drive 71
Hard Drive Tray 71
Adding Peripheral Drives 72
Drive Tray Handle 73
Release Button 73
Drive Tray 74
SAS/SATA 74
Chapter 7 75
7-2 Main Setup 76
Boot Features 78
•Type of CPU 79
•CPU Signature 79
•Microcode Patch 79
Chipset Conguration 84
North Bridge 84
Integrated IO Conguration 84
QPI Conguration 85
DIMM Conguration 86
DIMM Information 86
South Bridge Conguration 88
SATA Conguration 89
PCIe/PCI/PnP Conguration 90
Super IO Conguration 92
Serial Port 1 Conguration 92
Serial Port 2 Conguration 92
Console Redirection Settings 93
Console Redirection Settings 95
ACPI Settings 96
TPM Enable Status 97
NIC Conguration 98
•Factory MAC Address 99
•Alternate MAC Address 99
7-5 IPMI 101
BMC Network Conguration 102
7-6 Boot 103
7-7 Security 104
7-8 Save & Exit 105
Appendix A 107
BIOS Error Beep Codes 107
Appendix B 109
System Specications 109

Comentarios a estos manuales

Sin comentarios

Supermicro SuperServer 7047R-TXRF Manual de usuario Pagina 73

Comentarios a estos manuales

Relacionado con productos y manuales para Barebones Servidor Supermicro SuperServer 7047R-TXRF