Supermicro SuperServer 7048R-C1R4+ Manual de usuario Pagina 15
- Pagina / 132
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 7048R-
C1RT4+/7048R-C1R4+ up and running. Following these steps in the order given
should enable you to have the system operational within a minimum amount of
time. This quick setup assumes that your system has come to you with the proces-
sors and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specic components.
The 7048R-C1RT4+/7048R-C1R4+ may be employed either as a tower or mounted
in a rack as a 4U rackmount chassis.
2-2 Unpacking the System
You should inspect the box the system was shipped in and note if it was damaged
in any way. If the server itself shows damage you should le a damage claim with
the carrier who delivered it.
Decide on a suitable location for the SuperServer 7048R-C1RT4+/7048R-C1R4+.
It should be situated in a clean, dust-free area that is well ventilated. Avoid areas
where heat, electrical noise and electromagnetic elds are generated. You will also
need it placed near a grounded power outlet. Be sure to read the Rack and Server
Precautions in the next section.
2-3 Preparing for Setup
The box the system was shipped in may include two sets of rail assemblies, two
rail mounting brackets and mounting screws needed for installing the system into
a rack (optional kit). Follow the steps in the order given to complete the installation
process in a minimum amount of time. Please read this section in its entirety before
you begin the installation procedure outlined in the sections that follow.
Choosing a Setup Location
•Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufcient airow and ease in servicing.
- SUPER 1
- Manual Revision 1.0 2
- Release Date: October 9, 2014 2
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 1 9
- Introduction 9
- 1-2 Serverboard Features 10
- 1-3 Server Chassis Features 11
- 1-4 Contacting Supermicro 13
- Chapter 2 15
- Server Installation 15
- 2-4 Warnings and Precautions 16
- Rack Mounting Considerations 17
- Inner rail 18
- Outer rail 18
- Rail brackets 18
- Installing the Chassis Rails 19
- Installing the Rack Rails 20
- Chapter 3 23
- System Interface 23
- 3-3 Control Panel LEDs 24
- 3-4 Drive Carrier LEDs 25
- Chapter 4 27
- Installation Instructions 30
- Circuit Breaker 31
- Power Disconnection Warning 32
- ילמשח קותינ ינפמ הרהזא 33
- Equipment Installation 34
- Restricted Area 35
- Battery Handling 36
- Redundant Power Supplies 38
- Backplane Voltage 39
- Product Disposal 41
- Hot Swap Fan Warning 42
- Power Cable and AC Adapter 44
- (UL/CSA ) 45
- Chapter 5 47
- Advanced Serverboard Setup 47
- OPEN 1st 48
- IMPORTANT! 49
- 5-3 Connecting Cables 52
- 5-4 I/O Ports 53
- 5-5 Installing Memory 54
- Memory Support 55
- INTEL CONFIDENTIAL 56
- TPM/PORT80 57
- Serverboard Quick Reference 58
- 5-7 Connector Denitions 60
- Front Control Panel 61
- Rear I/O Shield 63
- GLAN/TLAN Ports 64
- Pin Denition 64
- IPMI LAN Port 64
- UID LED Status 64
- Other Connectors 65
- 1-2 Enabled (default) 68
- 2-3 Disabled 68
- 5-9 Onboard Indicators 70
- 5-10 SATA/SAS Connections 72
- 5-11 Installing Software 73
- SuperDoctor® 5 74
- 5-12 Onboard Battery 75
- Chapter 6 77
- Advanced Chassis Setup 77
- 6-2 Front Control Panel 79
- 6-3 System Fans 80
- 6-4 Drive Bay Installation 82
- SAS/SATA Backplane 83
- Mobile Rack (Storage Module) 84
- Enclosure Release 85
- Mobile Rack 85
- Mobile Rack Enclosure 85
- 6-5 Power Supply 86
- Chapter 7 87
- 7-2 Main Setup 88
- Boot Feature 90
- Power Conguration 91
- CPU Conguration 92
- Chipset Conguration 96
- North Bridge 96
- IIO Conguration 96
- IIO1 Conguration 96
- IIO2 Conguration 97
- •Number of CPU 98
- •Number of II0 98
- •Current QPI Link Speed 98
- •Current QPI Link Frequency 99
- DIMM Information 100
- •USB Module Version 101
- •USB Devices 101
- SATA Conguration 103
- •PCI Bus Driver Version 108
- •PCI Device Common Settings 108
- Super IO Conguration 110
- ACPI Settings 117
- 7-4 Event Logs 118
- View SMBIOS Event Log 119
- 7-5 IPMI 120
- •IPMI LAN Selection 121
- •IPMI Network Link Status 121
- 7-6 Security Settings 122
- 7-7 Boot Settings 123
- •Legacy Boot Order #1 124
- •UEFI Boot Order #1 124
- 7-8 Save & Exit 125
- Appendix A 127
- BIOS Error Beep Codes 127
- Appendix B 129
- System Specications 129
- Power Supply 131
- Operating Environment 131
- Regulatory Compliance 131
Relacionado con productos y manuales para Barebones Servidor Supermicro SuperServer 7048R-C1R4+
Barebones Servidor Supermicro 5038D-I Manual de usuario
(114 paginas)
(114 paginas)
Barebones Servidor Supermicro 188411 Manual de usuario
(122 paginas)
(122 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.163 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales